WeTek Community Forum

OpenPCTV for WeTek Play

envagyokenvagyok Posts: 226WeTek Community Member
I see Openpctv files in update.wetekos.com:8080 site.
Can someone tell some Infos?
I see 2 file type, one img and one tar.
It can install to nand or the sdcard?
Work both tuner?
It has tvheadend or vu+ or enigma tv server?
Can I download channellists, Censure etc?

Thanks for Infos.

Updated:

I try sdcard install the img version, it booted, comes many line in character mode, after 1-2 minutes stopped.. After that not responding the device.

Comments

  • graugansgraugans Posts: 18WeTek Community Member
    Re: Openpctv

    Hello envagyok,

    it looks like an image for the SD-CARD:
    Assuming you are on a linux box, after extracting the bz2 image
    $ sudo fdisk -l /tmp/openpctv-devel-20150206-wetek.img 
    
    Platte /tmp/openpctv-devel-20150206-wetek.img: 3670 MByte, 3670016000 Byte
    255 Köpfe, 63 Sektoren/Spur, 446 Zylinder, zusammen 7168000 Sektoren
    Einheiten = Sektoren von 1 × 512 = 512 Bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    Festplattenidentifikation: 0x0006b8a9
    
                                     Gerät  boot.     Anfang        Ende     Blöcke   Id  System
    /tmp/openpctv-devel-20150206-wetek.img1   *        2048       67583       32768    b  W95 FAT32
    /tmp/openpctv-devel-20150206-wetek.img2           67584     7167999     3550208   83  Linux
    

    FAT32 is usally not used on raw NAND flashes :)
  • graugansgraugans Posts: 18WeTek Community Member
    Re: Openpctv

    Further investigations:
    Get start,offset and image size information
    $ sfdisk -d /tmp/openpctv-devel-20150206-wetek.img 
    # partition table of /tmp/openpctv-devel-20150206-wetek.img
    unit: sectors
    
    /tmp/openpctv-devel-20150206-wetek.img1 : start=     2048, size=    65536, Id= b, bootable
    /tmp/openpctv-devel-20150206-wetek.img2 : start=    67584, size=  7100416, Id=83
    /tmp/openpctv-devel-20150206-wetek.img3 : start=        0, size=        0, Id= 0
    /tmp/openpctv-devel-20150206-wetek.img4 : start=        0, size=        0, Id= 0
    

    Now calcuate options for mount
    $ echo $((2048 * 512)) $((65536 * 512))
    1048576 33554432
    

    Mount vfat part of the image
    $ sudo mount -o loop,offset=1048576,sizelimit=33554432 -tvfat /tmp/openpctv-devel-20150206-wetek.img  /mnt
    

    Look into the image
    $ tree /mnt/
    /mnt/
    ??? boot.img
    
  • graugansgraugans Posts: 18WeTek Community Member
    Re: Openpctv

    Bad news, after burning 3.5GB to SD-Card the only thing I get from this is a kernel oops....
  • schamaneschamane Posts: 27WeTek Community Member
    Re: Openpctv
    envagyok wrote:
    I see Openpctv files in update.wetekos.com:8080 site.
    Can someone tell some Infos?
    I see 2 file type, one img and one tar.
    It can install to nand or the sdcard?
    Work both tuner?
    It has tvheadend or vu+ or enigma tv server?
    Can I download channellists, Censure etc?

    Thanks for Infos.

    Updated:

    I try sdcard install the img version, it booted, comes many line in character mode, after 1-2 minutes stopped.. After that not responding the device.

    again tvheadend, no enigma :(

    the other questions


    find . -iname tvhe*
    ./var/lib/opkg/info/tvheadend.list
    ./var/lib/opkg/info/tvheadend.control
    ./usr/bin/tvheadend
    ./usr/share/tvheadend
    ./usr/share/tvheadend/src/webui/static/app/tvheadend.js
    ./usr/share/tvheadend/docs/docresources/tvheadendlogo.png
    ./etc/tvheadend

    find . -iname enigm*
    no results :(

    find . -iname osca*
    ./var/log/Censure
    ./var/lib/opkg/info/Censure.list
    ./var/lib/opkg/info/Censure.control
    ./usr/bin/Censure
    ./usr/bin/Censure-pre.sh
    ./etc/Censure
    ./etc/Censure/Censure.conf
    ./etc/Censure/Censure.cert
    ./etc/Censure/Censure.user
    ./etc/Censure/Censure.srvid
    ./etc/Censure/Censure.whitelist
    ./etc/Censure/Censure.server
    ./etc/Censure/Censure.tiers
    ./etc/Censure/Censure.provid
    ./etc/Censure/Censure.ird
    ./etc/Censure/Censure.cacheex
    ./etc/Censure/Censure.ac
    ./etc/Censure.example
    ./etc/Censure.example/Censure.conf
    ./etc/Censure.example/Censure.cert
    ./etc/Censure.example/Censure.guess
    ./etc/Censure.example/Censure.user
    ./etc/Censure.example/Censure.srvid
    ./etc/Censure.example/Censure.dvbapi
    ./etc/Censure.example/Censure.services
    ./etc/Censure.example/Censure.whitelist
    ./etc/Censure.example/Censure.server
    ./etc/Censure.example/Censure.tiers
    ./etc/Censure.example/Censure.provid
    ./etc/Censure.example/Censure.ird
    ./etc/Censure.example/Censure.cacheex
    ./etc/Censure.example/Censure.ac
    ./lib/systemd/system/multi-user.target.wants/Censure.service
    ./lib/systemd/system/Censure.service
  • HenryLiuHenryLiu Posts: 4WeTek Community Member
    Re: Openpctv

    Get OpenPCTV for WeTek Play from here:
    https://sourceforge.net/projects/openpc ... etek_play/

    For Linux:
    http://sourceforge.net/projects/openpct ... d/download
    http://sourceforge.net/projects/openpct ... 2/download

    chmod 755 make-sdcard
    ./make-sdcard /dev/sdb openpctv-devel-20150207.wetek.tar.bz2

    For Windows:
    http://sourceforge.net/projects/openpct ... 2/download

    Included software:
    Linux 3.10.61
    Kodi 14.1
    VDR 2.1.8
    TVheadend 3.9-20150202+facee6f
    Censure svn10231
    mumudvb 2.0.0+r8db633a
  • envagyokenvagyok Posts: 226WeTek Community Member
    Re: Openpctv

    i dont find tvheaded..
  • HenryLiuHenryLiu Posts: 4WeTek Community Member
    Re: Openpctv
    envagyok wrote:
    i dont find tvheaded..
  • envagyokenvagyok Posts: 226WeTek Community Member
    Re: Openpctv

    Nice pictures, but better to know how can i enter this menu?
    Over kodi/services not find.
  • HenryLiuHenryLiu Posts: 4WeTek Community Member
    Re: Openpctv
    envagyok wrote:
    Nice pictures, but better to know how can i enter this menu?
    Over kodi/services not find.

    You can press any key when booting
    (You can see 'Press any key to enter setup,or 3 seconds later enter kodi' on the screen when booting)

    It needn't enable vdr/tvheadend services over kodi, they has been in the system. after you selected the PVR backend you only need to enable VDR VNSI/VDR XVDR(for vdr pvr backend) or tvheadend pvr addons in kodi
  • GuRuGuRu Posts: 588WeTek Community Member
    Re: OpenPCTV for WeTek Play

    damp but it works for 10 minutes, then the picture falls apart .. thanks
    problem with reduction of sound
    img:12ds93o1]img:12ds93o1]
  • ChristianTroyChristianTroy Posts: 1,913WeTek Community Member, Developers
    Re: OpenPCTV for WeTek Play

    unable to stat path might be related to the recordings path, try to set it to a path writable to the user running tvheadend daemon (or chmod 666 the recordings path)
  • digihoedigihoe Posts: 6WeTek Community Member
    Re: OpenPCTV for WeTek Play

    How do we compile it?

    git clone [url="git://git.code.sf.net/p/openpctv/code"]git://git.code.sf.net/p/openpctv/code[/url] openpctv-code
    cd openpctv-code
    ./scripts/loadcfg openpctv-wetek hangs after generating a few cfg files, what is needed?

    Thx!
  • digihoedigihoe Posts: 6WeTek Community Member
    Re: OpenPCTV for WeTek Play

    I use ubuntu 14.10, I see some linare-gcc reference, however Codesnakes OpenELEC compiles fine.
    digihoe@build:/openpctv-code$ sudo ./scripts/loadcfg openpctv-wetek
     CLEAN    kconfig-frontends  
     UNPACK   kconfig-frontends  
    ## Applying patch: packages/kconfig-frontends/patches/10-frontends_gconf_Makefile_in.patch
         CLEAN    configtools  
         UNPACK   configtools  
         BUILD    configtools  
    
    ########################################################################
    ##
    ## Loading configuration from:
    ##   ./config/defconfigs/openpctv-wetek.conf
    ##
    ########################################################################
    
    scripts/version2kconfig
    scripts/archs2kconfig
    scripts/platforms2kconfig
    scripts/machines2kconfig
    scripts/flavours2kconfig
    scripts/meta2kconfig
    scripts/use2kconfig
    Building build/config/Kconfig.packages.scripts/meta2kconfig: 11: packages/gcc-linaro/meta: Bad substitution
    Makefile:42: recepie for target ”build/config/Kconfig.packages” failed
    make: *** [build/config/Kconfig.packages] error 2
    

    Best regards!
  • HenryLiuHenryLiu Posts: 4WeTek Community Member
    Re: OpenPCTV for WeTek Play

    Fixed, Thank you!

    1.Get sources:
    git clone [url="git://git.code.sf.net/p/openpctv/code"]git://git.code.sf.net/p/openpctv/code[/url] openpctv-code

    2.Load the default config:
    ./scripts/loadcfg openpctv-wetek

    3.Select the default packages or function(optional)
    make xconfig or make menuconfig

    4. Build
    make

    5. Complete compilation, the rootfs will be save to binaries/binaries.wetek/openpctv-*.wetek.tar.bz2, You can use the make make-sdcard to create SDcard('devel-20150222' may be different from yours):
    ./make-sdcard /dev/sdb openpctv-devel-20150222.wetek.tar.bz2 #If /dev/sdb is your SDcard device.
    You can also use 'make-sdcard' script to create a rootfs image:
    ./make-sdcard openpctv-wetek.img openpctv-devel-20150222.wetek.tar.bz2

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    Here is the new rootfs image for WeTek Play(Just for testing):
    http://sourceforge.net/projects/openpct ... z/download


    digihoe wrote:
    I use ubuntu 14.10, I see some linare-gcc reference, however Codesnakes OpenELEC compiles fine.
    ...
    Best regards![/quote]
  • digihoedigihoe Posts: 6WeTek Community Member
    Re: OpenPCTV for WeTek Play
    HenryLiu wrote:
    Fixed, Thank you!

    1.Get sources:
    git clone [url="git://git.code.sf.net/p/openpctv/code"]git://git.code.sf.net/p/openpctv/code[/url] openpctv-code

    2.Load the default config:
    ./scripts/loadcfg openpctv-wetek

    3.Select the default packages or function(optional)
    make xconfig or make menuconfig

    4. Build
    make

    5. Complete compilation, the rootfs will be save to binaries/binaries.wetek/openpctv-*.wetek.tar.bz2, You can use the make make-sdcard to create SDcard('devel-20150222' may be different from yours):
    ./make-sdcard /dev/sdb openpctv-devel-20150222.wetek.tar.bz2 #If /dev/sdb is your SDcard device.
    You can also use 'make-sdcard' script to create a rootfs image:
    ./make-sdcard openpctv-wetek.img openpctv-devel-20150222.wetek.tar.bz2

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

    Here is the new rootfs image for WeTek Play(Just for testing):
    http://sourceforge.net/projects/openpct ... z/download

    Thank you HenryLiu for your efforts!

    However I still get some errors...
    Tried both eglibs and uclibc, but they both hang in the same place.
    Makefile:1338: recipe for target 'Congruence.lo' failed
    make[4]: *** [Congruence.lo] Error 1
    mv -f .deps/Constraint_System.Tpo .deps/Constraint_System.Plo
    mv -f .deps/Congruence_System.Tpo .deps/Congruence_System.Plo
    make[4]: Leaving directory '/openpctv/openpctv-code/build/build.wetek.uclibc/ppl-1.0/src'
    Makefile:1128: recipe for target 'all' failed
    make[3]: *** [all] Error 2
    make[3]: Leaving directory '/openpctv/openpctv-code/build/build.wetek.uclibc/ppl-1.0/src'
    Makefile:471: recipe for target 'all-recursive' failed
    make[2]: *** [all-recursive] Error 1
    make[2]: Leaving directory '/openpctv/openpctv-code/build/build.wetek.uclibc/ppl-1.0'
    Makefile:400: recipe for target 'all' failed
    make[1]: *** [all] Error 2
    make[1]: Leaving directory '/openpctv/openpctv-code/build/build.wetek.uclibc/ppl-1.0'
    Makefile:51: recepie for target ”rootfs” failed
    make: *** [rootfs] Error 2
    

    Is enigma2 interface working by the way?

    Best regards!
  • ZoomyZoomy Posts: 64WeTek Community Member
    Re: OpenPCTV for WeTek Play

    I've just installed this, but where is enigma2? All I'm seeing is Kodi. If enigma2 is non-existant, then what is the point in this software when we have Openelec?
  • takitaki Posts: 20WeTek Community Member
    uclibc/ppl-1.0/src
    I have same compilations error.how we fix it henryliu
    Otherhand enigma2 doesn't work with arm based device. only works x86 openpctv . Maybe somebody port gstreamer enigma2 for amlogi
  • takitaki Posts: 20WeTek Community Member
    I think that error based gcc 4.9.1
  • AdogaAdoga Posts: 40WeTek Community Member
    has anybody got this working? if yes how is it compared to OpenElec. I saw a video, it looks lightning fast and with a simple ui. I'm very much intersted. Is it worth it?
  • takitaki Posts: 20WeTek Community Member
    digihoe wrote: »
    Re: OpenPCTV for WeTek Play



    Thank you HenryLiu for your efforts!

    However I still get some errors...
    Tried both eglibs and uclibc, but they both hang in the same place.
    Makefile:1338: recipe for target 'Congruence.lo' failed
    make[4]: *** [Congruence.lo] Error 1
    mv -f .deps/Constraint_System.Tpo .deps/Constraint_System.Plo
    mv -f .deps/Congruence_System.Tpo .deps/Congruence_System.Plo
    make[4]: Leaving directory '/openpctv/openpctv-code/build/build.wetek.uclibc/ppl-1.0/src'
    Makefile:1128: recipe for target 'all' failed
    make[3]: *** [all] Error 2
    make[3]: Leaving directory '/openpctv/openpctv-code/build/build.wetek.uclibc/ppl-1.0/src'
    Makefile:471: recipe for target 'all-recursive' failed
    make[2]: *** [all-recursive] Error 1
    make[2]: Leaving directory '/openpctv/openpctv-code/build/build.wetek.uclibc/ppl-1.0'
    Makefile:400: recipe for target 'all' failed
    make[1]: *** [all] Error 2
    make[1]: Leaving directory '/openpctv/openpctv-code/build/build.wetek.uclibc/ppl-1.0'
    Makefile:51: recepie for target ”rootfs” failed
    make: *** [rootfs] Error 2
    

    Is enigma2 interface working by the way?

    Best regards!

    open terminal
    autoremove gcc 4.9
    apt-get install gcc-4.8 g++-4.8
    after no error for ppl compiletions


Sign In or Register to comment.
© Copyright 2014 - Creative Dreams | Powered by Vanilla
All times are UTC